I see that the Intel SSD Toolbox User Guide recommends running Intel SSD Optimizer weekly. Then reboot Windows 10/11 to allow it to reinstall Marvell 91xx Config ATA driver. Confirm the uninstll this Marvell 91xx device. Is that enough to confirm that it is now actually working? Expand Storage controllers or Other devices and then right-click the Marvell 91xx SATA 6G Controller to Uninstall device. Bit 0 - Data Set Management Supported = 1) and the Command Prompt check still shows that Windows 7 TRIM is enabled. I use the Intel 2.0 sata connection with no problems. If you can get it to work it will speed up a SSD I/O, R/W slightly. I have never been able to use it because it causes problems. Gigimundo 20Gbs Enclosure NVMe / USB 3.2 2X2. Marvell 91 xxm is a driver controller that works the 6 gig sata (3.0) connection on my Asus motherboard. Intel Management Engine (ME) Firmware Version 16. Intel SSD Toolbox shows that both SSDS have TRIM (i.e. Problèmes décran bleu sous Windows 10/11 Intel Management Engine (ME) Firmware Version 16. I've now installed the Intel RST driver (which appears to just change the ICH10 driver). The result was DisableDeleteNotify = 0 (which I understand to mean that the Windows TRIM commands are enabled)īut from what you said it appears that only indicates it is enabled in Windows because it couldn't have actually been working due to the driver I was using not supporting TRIM. I managed to install it ok, turn off legacy boot in my dell optiplex 3070 which was only way I can boot into windows 10. > fsutil behavior query disabledeletenotify Last week I bought a new Syba SI-PEX40057 SATA III 4 Port PCI-e 2.0x 2 Card with Marvell HyperDuo RAID Mode. When I did the initial installation (before installing the Intel RST driver) I used the Command Prompt to check whether TRIM was enabled in Windows as follows: If I understand correctly now, with the 3rd drive being a normal hard drive the Marvell 9123 Controller should be set to IDE and I can now see in Device Manager that this does not affect the AHCI driver file for the SSDs. So the drivers are changing that automatically on reboot as you indicated. That includes both SDDs, the 3rd hard drive, all the ATA Channels, the Intel ICH10 Family 6 Port SATA AHCI Controller - 3A22 and the Standard AHCI 1.0 Serial ATA Controller.Ĭhanging the Marvell 9123 Controller from AHCI to IDE in the BIOS changes the Standard AHCI 1.0 Serial ATA Controller to the Standard AHCI 1.0 Serial ATA Controller, which changes the msahci.sys driver file to the pciide.sys driver file. In Device Manager, everything appeared to be using Microsoft driver file version. I had read your previous posts about Asus and Marvell, Nick, hence I did not install the Marvell 9123 AHCI Driver. I think I now have a much clearer understanding than before. I hope the people here have been around long enough that they might have had some experience with this.Thanks very much Patrick and Nick. Obviously since I "paid" for these SATA 3 ports back in the day I would like to get full usage out of them, but how bad would it be to use SATA 2 with this HDD? I have benchmarked the SSD and it is clearly -not- getting full SSD speed.Ī) Is there any way to fix this? BIOS settings that I need to enable (AHCI is on I think)?ī) Would updating the drivers help at all? Windows seems to think it has the latest version, but I have heard that there can be driver problems with the Marvell SE9128?Ĭ) Is it more sensible to just use the Intel SATA 2 port? I have hear that the Marvell SE9128 was never very good even when it was working as intended. ThinkSystem Marvell SATA Controller Console Driver for Windows server. Unsurprisingly I have run into problems, Windows 10 (and my Motherboard/Bios) does not recognize the drive as a SATA, instead listing it as IDE in the BIOS and a HDD in windows. Hello there, I am upgrading my ancient machine with a P55A Fuzion Motherboard and two of the notorious Marvell SE9128 SATA 3 ports (the SSD is a 1TB MX500 2.5" which I am assuming works just fine).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |